Leviton OSP20-0D0 Occupancy Sensor Power Pack Ceiling Sensors 120/277 VAC
Containing both a 24VDC supply and a 20A line voltage relay for most models, the Leviton compact power pack provides low voltage power and line voltage control for Leviton Occupancy Sensors. Versions include Auto-ON and Manual-ON inputs for occupancy sensors, Hold-ON and Hold-OFF capabilities, and a local input for momentary or maintained dry contact switches. The internal relay can control up to 20A for a 120, 230, 277VAC or 347V ballast load and 20A for a 120VAC incandescent load. The OSP Power Pack Series is also used to supply power to the OSA Add-A-Relay model. The Power Pack conveniently mounts in a knockout hole of a standard junction box. The unit can be placed inside or outside the junction box with a simple twist-on nut. The internal relay can control up to 20 Amps at either 120, 230, or 277 VAC ballast load, 15 Amp for 347 VAC ballast load. Description Cat
NYCE NCZ-3010-2-HA Door Hinge Sensor - 4", Satin Nickel Finish
Manufacturer: NYCE Sensors Inc
Brand: NYCE Sensors Inc.
NYCE's wireless Door Hinge Sensor combines the features of a Door Sensor and ZigBee (802.15.4) radio into a single standard ANSI hinge device.Packed with intelligent features, the Door Hinge Sensor expands your network's possibilities - monitoring any type of door anywhere in the home - and all without any wires. For more information and product manuals visit: http://nycesensors.com/support/Included in the box:1. The hinge with ZigBee module attached.2. A pack of 4 installation screws.3. A pack of 2 set screws (Short & Long) with Hex key.Installation instructions:Phase 11. Open Network: Open up your controller's ZigBee network.2. Connect sensor: Remove the battery tab on the back, as soon as it is removed, the sensor will automatically try to connect with the hub.3. Configure: Depending on your platform, configure the sensor.4. Test: Gently tap the lever trigger and check if your controller receive a "Closed" or "Opened" status.Phase 21. Mount and secure the hinge sensor to the door frame side, ensuring it is properly seated in the door frame recess.2. Mount and secure the hinge sensor to the door edge side, ensuring that it is properly seated in the door edge recess. May need to apply pressure to the door to bring it into alignment.Phase 31. Open and close the door and see if the hub receives the status update.2. If it does not, it is very likely that the hinge is too wide apart. Install the supplied shorter set screw (1/8") to the set screw slot.3. If the shorter set screw does not work, try using the longer set screw (3/16").4. If the longer set screw still does not work, replace it with a size 4:40 pan head, slotted or Philips machine screw at your desired length.This product is NOT yet certified by SmartThings. However, a working driver is already included in their Driver database. It will connect with SmartThings Hub.THIS IS NOT CONTROL4 VERSION.
This product should be installed indoors . - Prior to installation, the device should be stored in a dry, dust- and mold-proof place - Do not install the siren in a place with direct sun exposure, high temperature or humidity- Keep away from chemicals, water, and dust - Ensure the device is never close to any heat source or open flame to prevent fire - Ensure the device is connected to an electric power source that does not exceed the maximum load power - The batteries are only a backup power source and are not recommended for use as the main power supply Model Number: ZSE01 Z-Wave Signal Frequency: 908.42 MHz Volume: 100dB Power: DC 5V/1A and 4 AAA (1.5V) batteries for back-up power Range: Up to 100 feet line of sight Operating Temperature: 14 Â°F to 122 Â°F Operating Humidity: â‰¤ 80% Installation and Use: Indoor only
GoControl LB65R6Z-1 Z-Wave Smart LED Recessed Retrofit Light Kit
The GoControl Bulbz 5 in.-6 in. Z-Wave Smart LED Indoor Recessed Retrofit Light Kit fits into 5 in. or 6 in. recessed lighting fixtures. It replaces old, outdated incandescent screw-in bulbs with clean and attractive, soft-white efficient LED lighting. The LB65R6Z can be controlled wirelessly when used in conjunction with a Z-Wave controller or hub using the controller's interface or with a smartphone, tablet or PC.