The WattStopper CX1051 Ceiling/Wall Occupancy Sensor,detects occupancy to control lighting in a wide variety of applications. These sensors provide superior coverage and performance with great energy savings. The WattStopper CX1051 Ceiling/Wall Occupancy Sensoralso comes with features such as Turning lights on/off based on occupancy, Useradjustable time delay, and sensitivit. Wattstopper's ASIC technology reduces components and provides greater reliability, Choice of four coverages patterns, Builtin light level sensor and Isolated relay for use with HVAC or other control systems.Note: 24V sensors use the following power pack (Sold Separately): bull; Watt Stopper BZ50bull; Watt Stopper BZ150
Wattstopper Lmsw-102-W Digital Switch, 2-Button, Infrared, White
Brand: Watt Stopper
LMSW-100 Series Digital Wall Switches are low voltage devices for energy-saving manual on/ off control of one or more loads from one or more locations. They are part of a Digital Lighting Management (DLM) system and can control any load(s) connected to DLM room controllers.
5150-W Shock Sensor (2-Wire, White) The 5150 series are the most low-profile glassbreak sensors in the industry. Adhering directly to the glass, the sensor acts as a visual deterrent for areas up to 10 feet (3 m). Advanced piezo technology powers the sensors, so no power is needed from the loop. The piezo generates its own electricity when it bends as the glass breaks. Because the transducer must bend for the sensor to go into alarm, false alarms are nearly eliminated. Reliable range verification testing allows the user to confirm the sensor's perimeter detection. The 5150 series sensors are ideal for retrofit installations where 2-wire protection is most practical.
GERI 12V 8-Channel Relay Module with Optocoupler H/L Level Triger for Arduino
Color: 12V 8-Channel Relay Module
Module description: 1. The module uses genuine quality relay, normally open interfaces Maximum load: AC 250V/10A, DC 30V/10A; 2. Using SMD optocoupler isolation, driving ability, stable performance; trigger current 5mA; 3. The module Operating voltage 12V; 4. The module can be high or low by a jumper setting trigger; 5. Fault-tolerant design, even if the control line is broken, the relay will not operate; 6. The power indicator (green), the relay status indicator (red) 7. The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient 8. Module size: 73mm*50mm*17mm (L*W*H) Module interface: 1. DC+: positive power supply (VCC) 2. DC-: negative power supply (GND) 3. IN1,2,3,4,5,6,7,8: can be high or low level control relay S1,S2,S3,S4, S5,S6,S7,S8 HIGHT OR LOW LEVER Relay outputs: 1. NO1,2,3,4,5,6,7,8: normally open relay interface 2. COM1,2,3,4,5,6,7,8: Common Interface Relays 3. NC1,2,3,4,5,6,7,8: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package: 100% Brand New 1*12V 8CH relay module Worry-free Warranty: 12 months worry-free product guarantee
Dakota Alert IRDCR-2500 Duty Cycle IR Kit, One IR-2500 & One DCR-2500
Manufacturer: International Supplies
Brand: Dakota Alert
The Duty Cycle Kit consists of one IR-2500 passive infrared detector and one DCR-2500 Receiver. The Infrared detector is capable of monitoring an area up to 100 degrees wide. With the integral mask, the detection area can be narrowed down to 20 degrees or anywhere in between. With the swivel mount, the IR-2500 sensor can be adjusted right to left up to 80 degrees and up and down up to 50 degrees. With three different sensitivity settings, the sensor can detect a person up to 12 ft., 25 ft., or 40 ft. away. The IR-2500 sensor is powered by one 9V battery (not included) and is designed for indoor or light duty outdoor applications under an eave or other protected location and will send a wireless signal up to 1/2 mile back to the DCR-2500 receiver (actual range will vary depending on the local terrain).
Sensor Switch CM PDT 10 Extended Range 360Â° Sensor Ceiling Mount Low Voltage Dual Tech (PDT)
Manufacturer: Sensor Switch
Brand: Sensor Switch
Classrooms are ideal applications for the CM PDT 10 Series Extended Range 360Âº occupancy sensor. When mounted at 9 ft, this sensor provides line of sight Passive Infrared (PIR) detection of walking type motions up to 28 ft in all directions. Additionally, the CM PDT 10 provides overlapping Microphonics technology to detect smaller motions and occupant movements that occur behind obstructions. This is important for classrooms filled with obstructions like shelving, hanging projects, or lab benches. When comparing small motion detection, the CM PDT 10 far out performs dual technology sensors on the market that are specified with 2,000 ft2 of coverage. Spaces with low ceiling heights are also best covered by the CM PDT 10. For example, when mounted at the 7 ft ceiling height of many distribution center pick aisles, the CM PDT 10 provides a 32 ft diameter pattern of coverage. Additionally, the CM PDT 10 may be used in combination with other sensors to customize coverage for very large or irregularly shaped spaces.
Hubbell Automation Omnidt2000Rp Omni Intellidapt Dual Technology Ultrasonic And Passive Infrared S
Manufacturer: Hubbell, Inc.
Hubbell Automation OMNITM IntelliDAPTÂ® Ceiling occupancy passive infrared sensor features self-adaptive technology and does not require manual adjustment. Sensor uses ultrasonic and passive infrared technologies to turn lighting ON and OFF based on occupancy. All-digital dual technology offers accurate turn-ONs and eliminates false-OFFs. It measures 4.500 Inch diameter x 1.500 Inch. Sensor has non-volatile memory for sensor settings and optional quick to install connector. It features relay and photocell control. Sensor can cover an area of 2000 sq.ft. Sensor is UL/cUL listed.